DuraTex is America's #1 Speaker Cabinet Coating designed to provide beauty and protection to wood speaker cabinets and road cases. Available now in half litre, 1 litre and 3.8 litre sizes, DuraTex is a superior performance Texture Coating that's easy to apply, beautiful and tough. This litre trial kit will give you enough DuraTex to coat say four 12" speaker cabs.
By tinting this DuraTex WHITE you can get any desired 'Pastel' and 'Medium' (lighter) colours. For Tinting Tips & Tricks sheet please click above Downloads tab.
DuraTex has tremendous adhesion to wood and other substrates. It rolls on easily with our special texture roller to create a tough, beautiful, weather resistant and easily maintained texture surface.
DuraTex is a blend of highly technical polymers, and special LOW V.O.C coalescents for creating beautiful high relief, durable textures. DuraTex requires no special primers because it's self priming.
With one gallon of DuraTex (doing a couple of coats) you can cover up to 9 square metres.
Test Drive DuraTex Roller Grade before buying a whole gallon. OR... it's just the right size for a smaller project or a recoat.
This DuraTex in a bag, in a box along with a texture roller gives you everything you need to give DuraTex a real good Test Run or to do that rehab you've wanted to do without having to buy a whole gallon.
This Kit is 1 quart or 0.95 Litres (for those of us in metric land) of WHITE and is just right to do 20 to 24 square feet ( a little over two square metres) of speaker cabinet surface ~ enough for say four 18” x 12” x 12” (45cm x 30cm x 30cm) cabinets with two full coats for each cabinet.
V.O.C.: 0.43#/Gal. (51g/L)
Solids by Weight: 63%
Solids by Volume: 51%
Resin System: Urethane Modified Terpolymer
Weight per Gallon: 11.5#
Cleanup: Soap and Water on fresh material, and Xylene or Toluene on dried material
All substrates must be clean and dry with no oils, silicones, waxes or other contaminants. Fill holes in wood substrate with DRYWALL SPACKLE, Bondo, wood filler or similar products or adhesion may be sacrificed. Sand surfaces before application and remove all sanding residue. Bare wood surfaces need not be primed; however a base coat of DuraTex® can be applied as its own primer.
By ROLLER: Apply roller grade by brush or roller to evenly coat the surface. A heavy first coat followed by a lighter second coat will give a milder texture. A heavy second coat will produce a more aggressive texture. Adding a small amount of water to the product will reduce the texture profile and can provide more of an orange peel texture.
By SPRAY: Apply spray grade by Hopper Gun, Pressure Pot HVLP or airless spray system in a complete even coat to the entire surface to completely seal and protect the surface. Once the base coat is dry, apply a spray texture coat by lowering the air break-up pressure. Spray pressures will be dependent on the type of spray equipment being used. Test the spray application technique first on a piece of cardboard and note pressure settings needed to accomplish the finish desired. Typical pressure pot base coat application uses only 15# of fluid pressure and 30# of air pressure. Texturing uses 20# of fluid pressure and only 5-10# of air pressure.
Higher air pressure = smaller dots. Lower air pressure produces larger dots. Higher fluid pressure + Higher air pressure produces a smoother, orange peel surface. Multiple color spatters create a “stone look” finish!
Allow all materials to dry thoroughly through air drying or forced drying in a baking oven. Do not exceed temperatures of 150°F for drying. Heating speeds up the curing process of DuraTex® but normal air drying will accomplish the same finished result over time. (Oven heating is optional, but facilitates rapid production throughput.) Do not apply this product to damp surfaces or when surface temperature is or will be below 60°F. and when Relative Humidity is above 70%.
To store containers that have been previously opened, spray a fine mist of water onto the coating surface in the container before resealing the lid. This raises humidity levels in the container and can help prevent the product drying or skinning over in the container.
KEEP FROM FREEZING. USE ONLY WITH ADEQUATE VENTILATION. WEAR NIOSH APPROVED ORGANIC VAPOR CARTRIDGE MASK WHEN APPLYING OR SANDING IN CONFINED AREA. DO NOT TAKE INTERNALLY. CLOSE CONTAINER AFTER EACH USE. KEEP OUT OF THE REACH OF CHILDREN! AVOID EYE AND SKIN CONTACT. WEAR GOGGLES. SHELF LIFE AT LEAST ONE YEAR WHEN STORED AT 75°F IN ORIGINAL UNOPENED CONTAINERS.
Revised May 2, 2011
To download a DuraTex Data Sheet please click here.
To download a DuraTex Safety Data Sheet please click here.
To download a DuraTex Tinting Tricks Sheet please click here.
We charge just a $15 per order flat rate for express shipping*. This covers one delivery attempt so please provide an address where some one is available to sign for courier delivery between 9am and 5pm weekdays. You can instruct us to ask the courier to leave your parcel unattended in a safe place, although please be aware that if anything happens to the parcel, neither us nor the courier company can be held responsible. Work addresses are a great delivery option. If using a work address please include the business' name.
* for some larger items does not apply to Australian remote island locations, some mainland remote locations (outside Darwin NT and Perth WA metro areas) or outside Australia. If unsure if you are entitled to $15 shipping it is best to contact us prior to placing order.